Clean and Protect: Shotguns, Handguns and Rifles!

Gun-tips® are foam swabs that are reusable and replace cotton swabs for cleaning all the action areas of your firearm! These are the newest and must have cleaning product for all firearm enthusiasts. Gun-tips are firearms cleaning foam swabs that are lint-free, washable and re-usable. Gun-tips are made in a range of sizes for cleaning slides, rails, trigger assemblies, crowns and other hard to reach places. The plastic handles are bendable and will not break or splinter like wooden sticks.


Swab-its Gun-tips: 24 Large Surface Cleaning Swabs in a bag

Swab-its® Gun-tips® 

  • 24 Large Surface Cleaning Swabs
  • Clean Triggers, Actions, Wells
  • Durable Plastic Handle
  • Lint-free Foam
  • Solvent and Lubricant Compatible
  • Washable and Reusable

About Gun-tips®

 Gun-tips are a strong and durable replacement for cotton swabs that do not leave lint and fibers behind. They come in four sizes and are flexible enough to round corners, but strong enough to resist breaking. Gun-tips are also washable and reusable. The 5” Large Surface swabs are especially effective for mag wells, dust covers, slides, AR lower and upper receivers, trigger assemblies and bolt carrier assemblies.

• A bag contains 24 Gun-tips®
• Each tip can be used multiple times
• Replaces cotton swabs
• Washable and reusable
• Lint-free and fiber-free

Front of package: Swab-its Gun-tips 24 Pack

Front of Package

Back of package: Swab-its Gun-tips 24 Pack

Back of Package

How to use and clean Swab-its® Bore-tips®

Caution: always ensure the firearm is unloaded and ammunition is not present when cleaning.

How To Use Bore-tips® Select the correct gauge or caliber Bore-tip, attach to rod or pull-through, and apply solvent to the tip.

Note: the Bore-tip is highly absorbent and will require less solvent than conventional patches.

Whenever possible, cleaning should be done from the breech forward. Use of a bore-guide is helpful in aligning the Bore-tip for straight insertion and keeping the rod centered in the barrel. If it is not possible to clean from the breech, precautions should be taken not to push debris into the action when cleaning from the muzzle.

(Inserting the Bore-tip at an angle can put undue pressure on the plastic neck and result in breakage.)

Run the Bore-tip down the barrel to apply solvent to the bore. Allow the solvent to soak several minutes to help loosen any lead or carbon build up. Remove the Bore-tip and attach caliber specific bore brush. Saturate the brush with solvent and run through the barrel several times.

Using the same Bore-tip as applied the solvent, push the loosened debris forward and blot off with a rag or paper towel as it emerges from the barrel. Continue pushing remaining debris out the barrel for a couple of passes, blotting on a dry cloth each time. The Bore-tip will trap fouling and release most debris upon compression on cleaning rag.

After blotting, the Bore-tip should be clean enough to continue using to remove the fouling until you are finished cleaning.
Once the Bore-tip seems to be yielding no new fouling, attach a clean Bore-tip to dry and capture any remaining debris. If lubrication is desired, use a 3rd Bore-tip to apply a light coating of rust preventative/lubricant to the bore.

Caution: before firing your gun, you will need to dry swab this lubricant away.  

How to Use Swab-its Firearm Cleaning Products

How To Clean Bore-tips®

For faster cleaning and drying use mineral spirits. Apply mineral spirits to the Bore-tip and squeeze/blot into an absorbent rag or paper towel. When the Bore-tip is clean, let dry and reuse. Using soap and water, squeeze and blot out any excess solvent or dirt. Next, wash the Bore-tip with a grease cutting soap and warm water. Once clean, rinse and allow to dry completely.

(Note: mineral spirits work best on petroleum based solvents, while bio based solvents may feel slightly gummy if not cleaned with grease cutting soap and water.) 

Clean Swab-its Gun-tips

Disclaimer: Always ensure the firearm is unloaded and ammunition is not present when cleaning. Swab-its and Super Brush LLC is not responsible for the cleaning of your firearm. Please make sure to follow all instructions provided by the manufacturer of your firearm when cleaning.